I learned two things that day; one never ever cut a tree that is hollow on the side towards the house when that tree is even close to the height that might reach the house. At that point things went bad and went bad fast.

Log Furniture Plan Book Furniture

The tree fell in the direction of the hollow, which by itself was not a bad thing.

I hadn’t planned on the top 30 feet of the tree separating upon hitting another tree limb and flying through the air as if some hand from heaven had reached down grabbed the tree and thrown it just far enough to add a new skylight to our bedroom. Fast forward a year, and most of that tree ended up in our outdoor fireplace as split logs, but the largest section still remained since it was too large to fit into the log splitter. Spade bits will work for the smaller diameters also.

Today’s rustic cabin furniture has come a long way. My goal was simple, build two tables for use on our patio that could withstand the weather, the kids and a couple of retrievers, and finish them enough so that my wife could not unknowingly say she mistook them for firewood. Jones’ taste have a bad habit of disappearing or meeting an unfortunate end?

I set off on my first attempt at creating log furniture. This tree was standing dead for one year, and had been on the ground for another, it supplied slabs for the bench and the tops of my tables were simple end cuts from the log. The end cuts were approximately 24” wide and were taken some 50 feet up the old tree.

This allowed me to merely lock the log into my vise and begin cutting the tenon. Depending on the tree, you may be able to use straight limbs for these pieces. Use whatever wood is available that is just part of what makes rustic furniture unique.

I then clamped a piece of scrap log in the vise and practiced turning a tenon. Once completed cutting the tenons you will drill a mortise to receive each leg for the table.

I feel more confident that my blind joint used on the second table will hold up better in the weather as the joint is not exposed on the top, but time will tell. Now with rustic furniture you could stop here and not do any finish and that is often done.

You can use wood putty to fill any cracks or holes, but if the furniture is to be left outside be sure and use exterior putty. Within an hour or two you can make these tables, less if you have the logs lying around. Drill a few holes into whatever lumber you have to accept the legs, insert the legs, apply some glue and voila, you have just finished your first rustic furniture piece. Its projects like this one that keep frustrated craftsmen like me out of therapy, it’s simple, fast and looks great when you’re finished. That’s all you will need to complete the woodworking portion on your log furniture. Over in the metal shop, something to cut your metal, a welder and another angle grinder will get the metal frame work done. Once a woodworking project is done, we’re always looking for the next mission. Most of us are wary of an author’s claim or a publisher’s book pitch, and we have more faith in the comments from someone who has actually read the book. This collection includes the most popular and bestselling books and videos on woodworking and shop projects. You’ll learn about making a door with a frame and panel layout, and rediscover the joinery that’s best for building doors. Don’t try building desks without referring to this first!

All you really need is a little inspiration. You’ll be amazed at how simple it is to unlock your imagination. Some of these are what you’d call furniture wood types, while others are only suitable for rough carpentry or shop projects. Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. All the tips, tricks and instruction you need to complete the projects, all in one place. Style that does not sacrifice quality, because you want your beautiful woodworking projects to last.

Buy Wood Working Project Plans Books and DVDs

You get all of the above with our download, plus we’ll let you in on a secret. With as little as three pieces of wood and a couple of clamps, you’ll create something that you’ll swear by in years to come. Get your free guide and a free project plan today!

You already know how to make a dovetail joint, in the basic form, with either a dovetail saw or a dovetail jig. But dovetails don’t stop there, especially when it comes to building accurate period furniture and better-looking dovetail drawers. The hard part is figuring out how to use the software after you open it up. Learn which wood finish you really need for the project or wood you’re finishing. To ensure that there are no problems, we’ve disabled your ability to shop for a moment. Superb step-by-step photographs and excellent working drawings help ensure success for both amateur and experienced builders. Each project takes from just a few hours to a weekend to complete, making this book an ideal resource for transforming your outdoor décor. Perfect for basic woodworkers and just right for anyone more experienced who wants a “filler” project. Why compromise with mass merchandise when you can make your own?

Those that do are featured in our magazine, on our website, in videos and some are available in print and digital plans. It’s bursting with beautifully made projects that will inspire beginners to try their hand at furniture making, perhaps for the first time. For the more advanced, there are plenty of challenges to stretch your skills and advance your understanding of this fine art. The styles vary widely ensuring something for everyone’s taste. You’ll find just the storage project you are looking for. The comprehensive woodworking sourcebook. Now you can have expert information, guidance, and instruction all in one book!

Making Outdoor Log Furniture is Quick and Easy

Use your woodworking skills to create practical storage solutions for your home. Included with each project is a full-size pattern. Woodworkers will simplify their lives with the projects in this book, and get the satisfaction of using what they make. Each project provides step-by-step instructions, exploded diagrams, and a helpful cutting list to minimize waste and guarantee success. In this book you will be walked through the assembly process after learning a short, brief history on how the piece of furniture was used and evolved over time. Traditional furniture withstands the test of time and is challenging to build. Granted, there are not too many square parts to most chairs, and compound angles can be intimidating. The articles in this book, should help dispel any questions you may have about chair building.

You can make them better than the average commercially made models. The projects, will help build skills while resulting in furniture worthy of passing down generations. Detailed step-by step instructions, complete working drawings, and cut lists are included.

You’re sure to find more than one project that will inspire you. Photos of finished pieces provide additional inspiration. Whether you’re buying for yourself or for a client, sometimes you need something really special, something at the very top of the quality ladder.

You can’t find that work in a furniture store or a manufacturer’s catalog.

You have to go to the source, to the men and women whose refined sensibility and meticulous craftsmanship enable them to produce truly distinctive furniture. Bringing you to the source, to those craftsmen, is what this book is all about.

It covers joinery relating to 18th-century furniture styles, as well as the demanding techniques required to complete ornate period pieces. Turning and carving, as well as building accurately, are all included in a highly visual format. If you love period details and long to create them, you will want this book. Among the many useful projects, you’ll find a handy bench that doubles as a storage chest, a step stool that converts to a comfy kitchen seat, and a fold-down bed that features a drop-leaf desk. Plus, each project includes detailed plans, expert instructions, and helpful tips to ensure your finished piece is built to last. Miller, a professional furniture maker, includes instructions and plans for seven chairs. The straightforward plans and instructions make it possible for any woodworker to complete these projects. There are also new chairs included in the color gallery. Each of the seven projects includes clear instructions, measured drawings and cut lists. The eight wonderful small cabinets in this book will inspire novice and intermediate woodworkers to create a project that showcases not only their treasures, but also their talent. All you need are a few essential tools, a little bit of space for a basic workbench, and the desire to make something with your own hands. It eliminates any fears as it demystifies the craft. It begins with an understanding of the minimalist mindset and quickly details how to make a small space productive while outlining the most efficient tools for a woodworker.

Each piece of equipment is explained and techniques and instructions for keeping each piece sharp and well-maintained are provided. Each project not only develops woodworking skills, but also outfits a small shop. Ultimately, it’s the handmade pieces of furniture that become the family heirlooms for generations to come. Ranging from boxes and trays to tables and cabinets, the stylish yet straightforward projects require only a limited number of hand and power tools and will enhance a woodworker’s joinery abilities as they progress from biscuits and dowels to dovetail and mortise and tenon joints. This type of furniture is very sturdy and long lasting, doesn’t show minor damage from children and pets, and it looks great!

Invest in a few tools and you can make all your own furniture almost for free.

I really, really like furniture like this. Depending on the piece and how it’s made, this furniture could last multiple lifetimes with just minor touch up and repairs. If you still feel unsure, then visit a big bookstore in a major city and spend a few hours looking at the log furniture books. Buy the best one or two if they look helpful. There is so much out there to choose from and a lot of fun options. Look closely to see the defects from pine beetles. This adds a lot of character, in my opinion. This is in stark contrast to high dollar custom furniture with white upholstery that no one gets to use because “it might get dirty”. Let’s start with a dry, well-seasoned, crack-free log that’s at least 17″ in diameter and about an inch shorter than your saw’s guide bar. With your project log cut to length, elevate and brace it for ripping by supporting it on a mound of scrap wood. Be sure that the supporting scraps run parallel to the project log (to avoid setting up a possible kickback situation), and that the block to be ripped is firmly seated and not wobbly. For these crafts, the slabs should be between 1 1/4″ and 2 1/2″ thick. To rip, first eye down your saw to align the guide bar with one of the outside edges of the log.

Making Log Furniture for Beginners

Now, holding the saw parallel to the edge of the log, begin the first ripping cut. This first, half-round edge slab should be at least 2″ thick, since it will serve as the top of a bench or table. After ripping the entire log into slabs, choose two flat pieces to serve as the bench’s legs. Legs for stools, low benches, and chairs will need to be about 13″ high, while end tables and larger benches will require 16″ legs. This can be safely accomplished by using nothing but one of your booted feet as a clamp if you keep that foot well away from the action, work slowly so as not to force the cut, and keep your eyes on what you’re doing.

You can also brace the slab with three wooden dowels driven firmly into holes bored into the elevated platform. Begin the cut at the end of the slab farthest from you, using a smooth, sweeping, in-down-back motion that draws the saw toward you and off to one side. To execute a curved cut without executing yourself, trace along the pattern line with the saw, making the first cut no more than 1/4″ deep, and repeat the process until the slab is cut completely through. After both legs are cut, choose a half round slab for the seat (if you’re building a bench) or top (if it’s to be a table). With the notches marked, lay the half-round slab on a flat surface, and brace it as you did when you were cutting the legs. When sawing the leg notches into the top, first make a “down” cut just inside each of the scribed lines, to a depth of no more than half the thickness of the slab. Now use a hammer or the back of a hatchet to knock the thin “wafers” of wood out of the notches. To smooth out the ridges that will be left in the bottoms of the notches, “plane” your saw carefully from side to side along the bottoms of each notch, taking care to keep both of the notches the same depth. Before driving the legs into their slots, place them in position and eyeball the fit. If either leg is too wide for its notch, work it down a bit with a heavy wood rasp. To seat the legs, first place a piece of scrap wood across the bottom of each to act as a buffer, then use a hammer or some such to do the pounding-in chores. If a leg fits too loosely, you can always drive some thin wooden wedges between it and the sides of the notch to shim it up tight. If you wish, you can further secure the legs to the top with dowels (which is the most aesthetic method), wood glue, or even nails or screws. With the bench (or table) completed, plane the top smooth with your saw, then use a rasp to complete the rough-finishing chores. But be careful not to overdo it; log furniture is supposed to look rugged.

You may wish to sand the top surface a bit, then wipe the entire project clean and apply a finish that’s appropriate for the use the piece will receive. For indoor furniture, natural wood that is lightly oiled is hard to beat. With a bit of practice, a competent sawyer can knock this project out in just a few minutes. In addition to the project log, you’ll need two shorter logs from which to cut supports. You’ll find tips for slashing heating bills, growing fresh, natural produce at home, and more. That’s why we want you to save money and trees by subscribing through our earth-friendly automatic renewal savings plan.

This one features one large door with shelves inside. It could even be an end table or night stand. Build one with these free woodworking plans. With a few simple tools, they made what they needed with what they had. Would be perfect for a family room or games room. Instead of taking a risk and losing them in the woods, display them with this golf ball display cabinet. Made of solid wood, this rack will hold 42 balls and features a hinged glass door. Its a fun project to make and a popular one as well.

We do not provide support for this software. Most drawings do not have instructions, its assumed you can build it based on the completed drawing provided. This web site is optimized for viewing on a screen resolution 1680×1050. And books and resources on woodworking vary greatly in their level of difficulty and expertise, just as woodworkers and carpenters all have different levels of experience.

Woodworking Books and Videos

Fortunately, most log home furniture projects can be completed easily by someone who has a little woodworking knowledge and has built one or more easy projects. Ted is now semi-retired, but he does keep his hand in things by teaching a wood turning class at a technical college. You’ll even know which tools you will need to complete the project. Detailed instructions and pictures help make your woodworking projects easy. In addition, as you know, you can take a regular furniture pattern and make it look more rustic, simply by using a rustic finish and by choosing rustic hardware. And, because of the huge selection of woodworking patterns, there is something for everyone. Whether you are a beginning woodworker, you are teaching a child or grandchild, or you are experienced, you will find projects at your skill level. Woodworking tutorials – access to 150 of them. Videos that show you give you how-to information that you would have to attend a class to get. That means that you can use it for 60 days, try a couple of projects—and return the collection if you decide that you don’t like it. In my book, that’s a risk free guarantee!

It’s a great value, for just the price of a dinner for two, at a local restaurant. There’s something satisfying about making a piece of furniture that still reflects the unique nature of the original wood. Finished pieces, although usually described as “natural” or “rustic,” can be surprisingly at home indoors or outdoors. The environmental movement is helping to fuel different strategies for home maintenance and decorating. From its beginnings as a pioneer method for creating useful, inexpensive furniture from what was on hand, this versatile style has grown into a 21st century cottage industry. This furniture is sturdy, easy to make, and has an artistic appeal that transcends décor styles. The drawknife can be used both to remove bark from logs and to make tenons, a type of joint that has a protrusion on the end of one log that fits into a mortise (cavity) in another log. Learning to use a drawknife effectively is a useful, but taxing, skill to acquire. Becoming familiar with drawknife work will give you excellent control over the construction of your pieces.

This is an area where log furniture really shines. Small imperfections in the wood, like knots, slight bends or ridges, make each piece distinctive. It takes about a year for most woods to air dry properly. Air dried wood is a solid option for most projects, but the drying process takes time and will create a few cracks. Part of the artistry of working with logs is in showing each element to advantage and concealing imperfections like cracks and unsightly knots. Woods that have been professionally dried have fewer cracks, but they can be quite expensive. Fire killed woods are another potential source of wood for log furniture projects.

Forest fires leave standing wood behind that’s sometimes usable. Fires will typically burn diseased trees faster than moisture laden healthy trees, so fire killed trees are more likely to be sound than scavenged deadwood. Often sections of bark have fallen off too, eliminating some of the prep work for you. Deadwood can be an easy choice, but be careful not to bring home insect infested logs or logs that have concealed dry rot. There are also a couple of instructional videos at the end of the list that will give you a better idea of what’s involved in completing a log furniture project. For your reference library we also offer books on sharpening and drying wood to prepare for your new log home furniture.

Free Woodworking Projects and Downloads

This book contains material lists and tools needed, drawings and dimensions for 20 common log furniture projects. This book also includes step-by-step assembly and finishing instructions. Join our e-mail list to be the first to find out what’s new!

Over 200 pictures and illustrations and easy to understand directions. This beloved bestseller gives you the how and why on living your best life with less clutter. Tired of being told to act like an extrovert?

Ten years ago he started building with logs and has never stopped!

Among others, it has 15 pages on tools, 35 p. Fortunately, this one is a useful, helpful, and clear guide to the art of making log furniture. While the authors are thorough in their details, they are careful to continually remind the reader to infuse his or her own creativity in the process, leaving some of the specifics of certain the projects up to the reader’s desires and imagination. All in all, a wonderful introduction to a craft that produces tremendous rewards for all levels of ability, and one which is not at all inappropriate for those who have absolutely no woodworking experience nor a workshop full of expensive power tools, such as myself.

I highly recommend this book to anyone who likes to work with wood, loves the look and feel of log furniture but doesn’t want to pay the often prohibitively high prices for such items in retail stores, and/or wants to explore a new, highly rewarding hobby (or perhaps even a profession). In fact my first project is a log bed (under construction at this time). The plans are reasonably clear and concise and there are lots of tips that can help reduce the “ooops” factor when building your first piece of furniture.

Furniture Plans

The tools required are simple and fairly inexpensive. If you want to build your own log furniture then buy this book. To answer any shipping questions, please call 406-886-2500.